Exactly How to Install a Bath Tub: Install an Acrylic Bathtub as Well as Tub Surround

Services

They are making a number of good points relating to How to Install a Bathtub Yourself as a whole in the article beneath.

Installing a tub isn't specifically brain surgery, but it does need strong plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old tub with a brand-new one is also a moderately tough task. If the old tub is easily obtainable, the task can move rapidly; if you have to open up a wall surface to remove the old tub as well as place the brand-new bathtub, the task is much harder. In either situation, the task is within a home handyman's skills, although you will require an assistant to vacate the old bathtub and set in the new one. Make certain you have actually qualified on your own for the job and fit trying it. Rather than hiring a specialist to take control of a halfway-completed project, it is much better to think about using one before you begin. Possibilities are you might require a specialist plumber to make tube connections.
This short article will certainly aid you mount a new bathtub in your restroom if you have actually currently acquired a brand-new tub and don't need to alter the setup of your previous water pipelines.
Your tools and material checklist ought to make up the following:

New Bath tub

Hammer

Pipeline Wrenches

Prybar

Shatterproof glass

Degree

Pliers

Adjustable Wrench

Putty Knife

Screwdriver

Cold Blade

Tape Measure

Pipe Caps

Removing Old Taps

If you need to replace old faucets with brand-new ones as a part of your installment, after that the first thing you must do is detach the water system. After doing so, switch on the taps to drain any water continuing to be in the system. The procedure of eliminating the existing faucets can be rather problematic due to the restricted accessibility that is usually the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the taps. Have a cloth all set for the staying water that will come from the pipes. As soon as the supply pipelines have been removed, use the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from transforming during this procedure. As soon as the taps have been eliminated, the holes in the bath/basin will have to be cleaned of any kind of old securing substance.
Before proceeding to fit the new taps, compare the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.

Suitable New Taps

If the tails of the new faucets are plastic, after that you will need a plastic adapter to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end provides a link to the existing supply pipes.
If you require to fit a monobloc, after that you will call for minimizing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next, place the faucet in the installing opening in the bath/basin making certain that the washers are in area between the tap and also the sink. Protect the faucet in position with the producer supplied backnut. Once the faucet is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with normal faucet ports. The previous kind ought to be attached to the tap finishes first, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.

Mounting the Tub

Using both wooden boards under its feet, put the bathtub in the called for position. The wood boards are useful in equally spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 small factors.
The next objective is to ensure that the tub is leveled all round. This can be achieved by inspecting the level as well as readjusting the feet on the bathtub up until the spirit level checks out degree.
To set up faucets, fit all-time low of the furthest versatile faucet port to the ideal supply pipe by making a compression sign up with; after that do the same for the various other tap.
Turn on the water and inspect all joints and also new pipework for leaks as well as tighten them if essential. Fill the bathtub and additionally examine the overflow outlet and the typical electrical outlet for leakages.
Finally, repair the bath paneling as explained in the supplier's user's manual. Tiling and sealing around the tub must wait till the bath tub has been used a minimum of once as this will resolve it right into its last placement.

Planning for the Installation

Firstly, the supporting framework supplied with the bathroom must be fitted (if called for) according to the supplier's guidelines. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is essential to ensure that if the tap includes a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the faucets system to avoid stress on the tub.
Fit the versatile faucet ports to the bottom of the two taps utilizing 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet with the hole in the bath. Use the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you utilize all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bath ought to now be ready to be suited its last placement.

Tiling Around the Bathtub

In the area where the bath meets the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the installation can move enough to crack an inflexible seal, triggering the water to permeate the wall between the bathroom as well as the tiling, resulting in problems with dampness and also feasible leaks to the ceiling below.
You can pick from a range of coloured sealants to blend in your fixtures and installations. They are offered in tubes and cartridges, and can sealing gaps approximately a width of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of soaked paper or soft rope. Keep in mind to always load the tub with water before securing, to enable the movement experienced when the bathtub remains in use. The sealer can break fairly very early if you do not take into consideration this movement prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally quickly readily available on the market. It is advisable to fit the floor tiles using waterproof or water resistant adhesive and also grout.

A Step-by-Step Guide to Installing a Bathtub

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

Remove the Existing Bathtub

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

Choose the Right Bathtub

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

Install the Plumbing and Ledger Board

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

Install the Bathtub

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

Hook up the Plumbing

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

Install the Bathtub Surround

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

I am very excited about How to Install a Bathtub and I'm hoping you appreciated my entry. Sharing is good. You just don't know, you may very well be helping someone out. Thank you for taking the time to read it.

Call Today